Contact Us

If you have any questions, you can contact us. Required fields are marked *

How to laying of cement concrete Pavement slab step by step

How to lay paving | Cement Australia

In a wheelbarrow, mix one 20kg bag of Concrete Mix with 2.5 litres of clean water with a shovel and using a trowel place the mixed concrete up against the side of the pavers in the trench you have dug. Angle the surface of concrete half way up the side of the paver and smooth the surface using a wooden float.

Learn More

10-Step Process of Stamped Concrete

Stamped Concrete Step-by-Step Overview. Installing stamped concrete is challenging. You may be able to manage pouring and placing the concrete with minimal issues, but if you don't get the imprinting process just right, you'll be left with a permanent slab that can be difficult and expensive to repair.

Learn More

Should I Leave a Gap Between Concrete Pavers?

Matching the Gap to the Paving. As to whether one should leave a gap between concrete pavers, the short answer is yes. However, the size of the gap will depend on the type of paver as well as the type of paving. For instance, if you're laying concrete pavers for a patio, make sure they're close together with edges touching.

Learn More

How to Add Concrete Steps to an Existing Concrete Slab

Rest a 2-by-4 board across the top of the form and use it to scrape the excess concrete off the top step. The board will level the concrete with the top edge of the form. Repeat this on each step, working your way down. Wait until the concrete turns a light grey before moving on.

Learn More

How To Pave a Pathway - Bunnings Australia

Spread this mixture over the pathway with a shovel. Use a broom to sweep it into the cracks between the pavers. Using a hose, lightly spray the path, which will help the mixture to harden. Repeat this process until all of the cracks between the pavers are filled. Let this mixture harden before walking on the pathway.

Learn More

Building Foundations: A Step-By-Step Guide | Homebuilding

3. Use String Lines to Mark Out Your Building Foundations. Start marking out the walls, starting with one corner point (Image credit: Homebuilding & Renovating) Start marking out for the walls. Set up timber hurdles at the end of each wall, out of the way of where the digger will need to be.

Learn More

DIY Concrete Patio in 8 Easy Steps | How to pour a cement slab

How To Pour a Concrete Slab Thoroughly dampen the gravel. Start placing the concrete at one corner of the form while a helper uses a shovel or hoe to spread it (above). Pour the concrete up against the form and compact it into all corners with a square shovel or mortar hoe; with a hoe, push- don't drag the concrete.

Learn More

How to lay porcelain paving | Bradstone

STEP 3: Establishing lines and levels. The paving needs a slope or fall of around 1:60, i.e. 17mm of fall for every metre width or length of the patio. Use one taught string line to guide alignment along the length of the paving, and a second along the breadth. When laying, you should use a straight edge and spirit level to repeatedly check

Learn More

How to Lay a Patio

Wet and dry cement can cause irritation and burns, so handle carefully, covering skin and immediately washing off any cement that accidentally makes contact. Always wear protective gloves, safety goggles, and a dust mask when mixing concrete. If you're using heavy paving slabs or lifting any other heavy items, ask someone to help. Aftercare

Learn More

Pouring & Finishing Concrete Slabs | QUIKRETE: Cement and

When working with cement-based products, always wear eye protection and waterproof gloves. Step 1. Prior to placing concrete forms: Construct the form with 2x4 or 2x6 lumber and secure in place by wood stakes and deck screws. Excavate the slab area to a depth of about 7 inches, allowing 3 inches for a gravel base and 4 inches for concrete. Step 2.

Learn More

How to Lay Block Paving | Laying Guides | Bradstone

Step 3: Edge restraints. Kerbs must be laid and fully haunched on a concrete bed in order to provide adequate edge restraint to the block paving. Using a concrete mixer, mix 1 part cement and 6 parts ballast to create the concrete foundation, which should be 100mm thick in depth.

Learn More